How To Remove Rust From Bike? Easiest Steps!

Dealing with rust, corrosion, and such things is a common problem of almost every biker. I know “rust” itself is enough to ruin the whole aesthetic of your loving vehicle.
But thankfully, there is a silver lining, you know! You won’t have to go to the repair stores just to erase rust from your bike. It’s pretty easy to remove, and most interestingly, you can do it yourself, yep!
Here, I’m going to talk about how to remove rust from the bike, and that too without working really hard. So let me show you a number of different techniques to get the job successfully done.
Trust me, if you take all my suggestions and tips, nobody can stop you from removing rust!

Breaking Down Different Methods
Removing the rust from bikes isn’t rocket science. So, you don’t have to spend all your money and time to get rid of this problem. Therefore, to make things easier, I have done some research on several methods that you might find useful.
And good to know, these techniques are very effective in order to remove rust. Check out all the details of the following processes for cleaning the rust in the best way possible.

  • Baking Soda
  • Vinegar
  • Coca-Cola
  • Chemicals
  • Scrubbing
  • Lemonade

Needless to say, these ingredients will come in handy when it comes to removing the rust from your bikes. So, without more chit-chat, let’s get started now:

  • 1. Baking Soda

First up is the most common and probably the best method. If you can handle the baking soda properly, then you’re getting a better result without a doubt. As the soda does a gentle cleaning on the surface, there is absolutely no chance of damaging your lovely bike.
In a nutshell, the soda forces the rust to fade away if you manage to follow every single instruction correctly. Check these out:

Making the Paste

A strong paste can give you a much better result than you have expected. Let’s see how to make the paste appropriately.

  • Start the process by mixing the soda with the water.
  • Mix the equal amount of water and baking soda in a bowl or a bucket. Although there is no hard and fast rule about the exact amount of water and soda that should be used for making the paste, you can always count on your eyes and instincts.
  • After that, do the mixing thing until it becomes a paste. Be sure to make a thick paste. It will be a wise decision to keep extra soda or water so that you can utilize them later on.
  • For maximum support, you can add lemon juice if you really want. Although it’s not compulsory, lemons can increase the strength of the paste.

Pasting the Bikes

When you finish the job of making the paste, applying the paste is your next task. Be careful about this step unless you want the rust to remain on the surface of the bikes.

  • In order to apply the paste, you can use a spatula or similar equipment, such as a sponge or a brush.
  • Apply the paste all over the rusted parts with the help of these tools. Also, press the affected areas directly with the tools so that no areas stay uncoated.
  • Don’t let the paste drip down because that’ll start to fall down if the paste isn’t thick enough. So, give attention to that if you don’t want to redo the whole process.
  • Finally, leave the paste to get completely dry for more than 10 minutes. Afterward, you’ll notice the baking soda starts reacting with the rust.

Ready for Removal

Remember, if you don’t remove the paste with proper concentration, then you might damage your loving bike.

  • Let’s begin the removing process with the help of a scrub. Indeed, you can use other stuff like a sponge, toothbrush, scrub pads, or a plastic-build scrubber. Pick any suitable one according to your comfort or availability.
  • Notice the rust if they’re coming out or not from the bike as you start scrubbing. Soon, you’ll find that your bike is shining, which means it’ll appear to be spick-and-span.
  • But, if you, unfortunately, don’t see any kind of differences in your bike, you might have to go through the whole process again, keep in mind!

2. Vinegar

On number 2, I’ve picked up the “Vinegar” that might reduce your efforts of removing the rust. It includes a powerful acetic property that fights against the rust to take it out from your bike.

Splashing the Bike with Vinegar
In that case, you won’t have to make any paste to apply it in the rusted areas. All you have to do is simply add some vinegar into a spray bottle, and you’re done. After that, follow these steps below:

  • Start splashing the areas that are rusted and do scrubbing at the same time.
  • For scrubbing, you can take the help of a toothbrush or similar kinds of tools. But before using the brush, ensure to cover it with tinfoil and start scrubbing.
  • Apply more spray solution if you find it tough to remove the rust. The benefit of using the spray bottle is that you can easily add as many solutions as you want.

Upgrade the Process

After all the hard work, if you still find that the rust of your bike is invincible, be sure to upgrade the method by following the below-mentioned techniques:

  • Add a little bit of baking soda to the vinegar solution. This will enhance the strength and assist the solution to fight against the rust with more power.
  • Spray the mixed solution again on the rusted areas and scrub a little harder.
  • Feel free to soak the affected parts of the bikes into a vinegar solution if you’re too lazy to spray and scrub.
  • 10 minutes of soaking will be just fine to take all the rust out from the bikes. But, this will require a lot of extra products compared to spraying. It can cost you a little bit more as well.
  • Remember to rinse the bike properly. Because the longer the solution stays on the bike, the more the metal will corrode. Wash and clean up the bike thoroughly, and that’s it!

3. Coca-Cola

Well, let me reveal the reason for using “Coca-Cola.” Actually, it gets acetic properties, same as vinegar, which is comparatively higher in amount. So, it can react with the rust and remove it within a snap.
To erase the rust, you’ll need to follow the exact way of spraying. In that case, you should be a bit careful while using coca-cola because it’ll appear to be a bit sticky. So, that might corrode the metal if you don’t wash it properly. Be careful!

4. Chemicals

Compared to the Coca-Cola method, chemicals are more effective in terms of removing rust. In that case, purchase any of the best rust remover chemicals available from your nearest hardware shops for your bike.
Note: Don’t mix additional chemicals as mentioned previously like used in the other solutions.

Applying the Remover

Check all the details about applying the remover to get rid of rust or such things permanently.

  • Apply the rust remover on the rusted areas of the bike with the assistance of a brush or scrub.
  • Be sure to leave it for up to 30 minutes or an hour. Indeed, the time depends on the rust remover you’re using. Some take less time, and others take a whole night for the solution to work better.
  • For a quick and better result, pick a high potential remover from the store.

Removing Tactics

When the waiting period is over, use a piece of cloth to remove the rust along with the chemicals. Then, dispose of it quickly before it gets contaminated with other things.
Wash the bike with water (warm water is preferable), and then leave it for drying. Afterward, your bike will seem to be clean and rust-free.

5. Scrubbing

Usually, this method is used for bikes that don’t have major rust issues. Also, it can be utilized for eliminating the outer rust flakes if the rust of your bike seems too deep.
Scrubbing can be done by using a brush, sandpaper, steel wool, or even a crumpled-up tin foil ball. Just scrub onto the rusty surface of the bikes until the rust gets completely removed.

6. Lemonade

Lemonade or lemon juice consists of citric acid that’s capable of removing rust. If you can’t dissolve your bike due to the lack of sufficient vinegar solution, then you can pick lemonade as an alternative to get the job done.
On the other hand, you can spray the lemonade directly on the bikes, just like the vinegar and Coca-Cola process. In addition, mix some vinegar with the lemonade as it’ll make the solution stronger and effective.
Make sure not to leave the lemon juice for too long on the bikes and wash them thoroughly after you’re done removing the rust.

Safety Matters!

Since you’ll find a lot of chemicals included in the processes, there is a great possibility of getting injured or falling sick. So, you have to ensure your safety first and then start working to remove the rust. Some actions that you need to take before and between the processes are:

  • Put your plastic gloves on before you add vinegar to a spray bottle.
  • Wear safety glasses and gloves whenever you’re working with commercial chemicals.
  • Wash your hands straight away if any chemicals get exposed to your skin.
  • Seek medical help immediately in case your eyes get sprinkles of chemicals.
  • Use an area that has a sufficient amount of air supply to perform the processes.

What If the Rust Reappears?

Even after you master the methods of removing the rust, these little things can reappear after some time, especially if you’re not that careful about them.
So, you have to find out the reasons for their appearance and must take action to prevent them from reappearing. I’ve tried to discuss the origins of rust and also come up with some precautions. Let’s find out!

Why Does Rust Appear?

Speaking of the origin, rust is made due to the oxidation process. It happens because of the humidity of the air that disintegrates iron when it makes contact with the air.
The low humidity of air means less rust production. On the contrary, salt does the opposite by accelerating the rusting process.

A Few Suggestions to Keep the Bike Rust-Free

Removing the rust once from the bike doesn’t mean that it won’t appear again. But if you take proper care of your bike, then it might stay out of rust build-up.
So, feel free to take my suggestions to keep your loving bike away from rust:

Keeping the Bike under a Shaded Place
Always be sure to keep your bike under a shaded place that can protect it from rain and snow. It might be a great decision if you store the bikes in a climate-controlled area such as the entry point of your home.

Applying Oil or Lubes

Chains are considered to be the favorite spot of the rust to appear. So, you’ve to give more attention while you’re oiling the chains. In that case, you need to be patient.
Drop oil on the links and quickly wipe it off with a piece of a rag or clean cloth. Follow this technique from top to bottom, even if it takes a little more time. By doing that, there’s a good chance that your bike will stay out of rust.

Drying Out the Bike after Raining or Snowing

Due to the sudden weather changes, you might catch yourself under a rainstorm or snowfall along with the bike. In this case, don’t forget to wipe your bike off after you get back home safely. I think using a clean cloth or rag won’t be a bad idea.

Some Quick Tips and Tricks

Here, I’m giving you some special tips to help you maintain your bike in the best way possible. Ensure to note down the points below if you like to keep your vehicle in better condition.

  • Paint the bike after a certain period and restore the damaged paint to avoid rust and corrosion.
  • Oil the brakes, handles, and gears. But make sure that the brakes and the rims aren’t meeting each other as they hamper the efficiency of the brakes.
  • Don’t let the water stay on the bikes after getting wet from a trip, and always try to wipe off the bike with a dry towel.
  • Keep the bike protected from moisture by using a special Vaseline.
  • Take out the rusty screws and soak these parts into vinegar or Coca-Cola to make them rust-free.

Wrapping Up!

As you know, the writing on how to remove rust from bikes includes a couple of techniques to remove rust. So, you can choose any of one from the above-written procedures to get rid of “rusting issues” once and for all.
Stay safe and take proper care of your bike to use it for a longer period of time!

Leave a Comment

13 − 4 =